Chapter . Release Notes

Fix the display of the installed copy of the manual.

Prevent loss of system configuration when settings are changed.

If the "Delete all measurement data" process is interrupted, it will now be resumed.

Allow changing sensor model when only one requires a calibration table.

Ensure sensor helper loads for unknown sensor models.

Improved robustness against RS485 data corruption for ASCII protocols.

Improved memory usage for CSV generation with RS485 sensors.

Fix endianness for Galltec Thermo-Hygro KPC MS.

Fix Lufft WS 502 implementation.

Fix DHI formula in Evaluation helper.

Fix table sorting on clicking the header in the sensor list and other pages.

Fix statistics calculation for 'Thies FCA X - ASCII' and 'Vaisala WMT700 NMEA'.

	Warning
	You must delete and regenerate older files to correctly perform the statistics calculation.

Introduce a timeout for SCP communication.

Fix graphical issue in the web interface in Chrom(ium) versions 87 and up.

Fix rounding problem for negative values.

Make switch pre-time available for most sensors, again.

Enhanced startup system storage clean-up function for very large amount of CSV files

New IDS-20 Icing measurement system from Sommer Messtechnik

Fix high count statistic for potentiometric wind vanes when combined with several RS485 sensors

Add Lufft WS 502 with solar irradiance

Add Lufft WS 300

New Thies FCA X anemometer implementation for one-step calibration

Enhance performance for very large amount of CSV files

Fix EE071 Hygro-Thermo over RS485 implementation

Add body temperature value to the values read by Hukseflux pyranometer SR30, fix the solar irradiance values

New Hukseflux pyranometer SR30 implemented

New incoming long wave radiation Ein for pyrgeometers

Fix generate statistics if secondary statistics active and evaluations from Evaluation Helper configured

New DustIQ sensor implemented

Fix problem with resetting tunnel name to tunnel.ammonit.com in some cases

Add maintenance option to automatically delete oldest files in case of system storage shortage

Register if CSV statistics files were copied to USB flash-drive

Fix connect more than one Meteo-40 Modbus RTU slaves (SCADA) to the same RS485 bus

Add option to allow global access to SCADA server

	Warning
	If you use SCADA over USB-Modem you must allow global access!

More than one client IP addresses allowed for SCADA Modbus TCP

Fix user interface for set date/time over NTP

Fix save and send test email action

New dew point formula in evaluation helper

Fix start recording over LCD

Increase reliability of SCADA stored data request and summary statistic

New solar sensors pyranometer MS-40, pyrheliometer MS-57 and pyrgeometer MS-202

Connection of pyranometer MS-80A over shunt available

Fix TWS100 parser

New Plane of Array irradiance formula in evaluation helper (replaces effective irradiance)

New Soiling Ratio Isc index formula in evaluation helper (replaces Soiling Ratio)

	Warning
	If you had already configured Soiling Ratio evaluations, you will have to configure them again!

Fix Soiling Loss Index formula in evaluation helper

New sensors type Weather Station in Sensor Helper

New TWS100 integrated dust monitoring station

New Thies Hygro-Thermo compact over RS485

New NRG 200M Wind Vane with configurable slope

New Ampere meter in sensors list for easier configuration of the I-U Conversion Box

New Ampere meter formula in Evaluation Helper for Gantner modules used with Ammonit Soiling Kit

Separated save and send/copy test file for Communication Email/AmmonitOR/Copy

Fix double email, broken in 1.7.12

Thies barometer can be connected to counter input

Thies FCA X automatic request can be deactivated

Remove CMA 11 albedometer from list, can still be configured as two CMP 11

Fix Pyranometer Li-Cor LI-200SZ formula (broken in 1.7.16)

New formula for albedo in Evaluation Helper

New CMA 11 albedometer

New formula for diffuse horizontal radiation (DHI) in Evaluation Helper

Thies FCA X wind speed available with Thies protocol

Thies FCA X - Modbus RTU plain version for connecting more than four sensors to RS485-M

Thies FCA X inclination extended version over Modbus RTU

Fix out of range values in Thies 10-bit protocol for Dx channels

Fix evaluations missing in snapshots

Fix Silicon Irradiance Sensor SiS-13TC-T irradiance formula

Fix SCADA Modbus Register Map field order for Date/Time

Fix request hardware ID from Thies anemometer FCA X

Fix configure other sensors if no switch available

Fix RS485 Modbus RTU sensors signed long values parser

Fix parser for SMP10 over RS485-M

Fix pyranometer solar irradiance negative values for newly configured sensors

New Pyranometer MS-80A in sensor helper

New EE071 Humidity and Temperature Probe in sensor helper

Fix Secure FTP

Change in CSV files header for internal temperature 'T' to 'T;Avg'

New sensor EKO MS-60M RS485 pyranometer

New sensor EKO M-Box RS485 Modbus RTU adapter for pyranometer

Don't send snapshot if not explicitly configured

Fix automatic system storage clean-up for already sent CSV statistics files (see Section 6.3, “Statistic Data Files”)

New sensor EKO MS-80M RS485 pyranometer

New sensor EKO ML-01 pyranometer

New EC-10 Decagon soil moisture sensor

Add RS485 8 Hz measurement for one sensor

Add Secure FTP as method to transfer files, additional to SCP and FTP, SCP is still the recommended method

Do not show or log complete login IP address, for data protection

Fix RS485 sensors telegram freezes

New Thies Clima US VDTHP

Fix SDI-12 (broken in 1.7.12)

Fix save SCP (broken in 1.7.12)

Fix Meteo-32 stream map

New download SCADA Modbus registers table as CSV available

New Gill MaxiMet GMX600 weather station

New ultrasonic flow meter KUF2000

New Hygro/Thermo CS215 over SDI-12

Fix period measurement

Allow empty Gateway and DNS server for LAN configuration

Allow use of Switch Manager only with timer

Support two microphones for SM3BAT

Performance enhancement for actions if CSV files not required, e.g. send camera images

Automatically activate period channels on Meteo-40 M and Meteo-40 L

Add purely linear formula for NRG and Generic anenometers

New Vaisala WMT700 NMEA MWV

New Datasol MET Reference Cell

Fix SMP10 pyranometer Modbus registers

Improve email layout

Minor error connections

Meteo-32 stream map includes ZephIR Live data

Enhance CSV files generation reliability

Switch manager supports timer with two user-defined timeframes

Support 2nd, 3rd, and 4th statistical moment (variance, skewness, kurtosis)

Fix statistics interval value written in secondary and tertiary CSV files

Add system storage level to data snapshots

New lightning detector SkyScan SG1000

New Duty Cycle and Pulse Width measurement

Fix some problems when UI not in English

Fix files selection when "start date" parameter used

Fix switch manager label not shown in switches table

New Song Meter SM3Bat Detector

User interface usability enhancements

Allow delete empty Gust data files

New refresh camera image button

Increased MARS stability

Fix CSV file generation, which broke in 1.7.7 in some cases

More updates of UI translation

Fix SDI-12 allowed address range

Fix Modbus RTU sensors configuration migration

Fix recording off after upgrade

Update of UI translation

Add internal V, I and T to Evaluation Helper

Fix source data access for certain RS485 serial settings

Fix internal voltage and temperature available in Switch Manager

Always reduce online traffic when logged in, not only for satellite connections

Fix USB flash drive source data download

Deactivate Gusts files generation if no trigger evaluation configured

New Reflectometer CS650 over SDI-12

New Wind Direction Potentiometric formula in Evaluation Helper

Fix delete evaluations from evaluation helper

Fix compressed files download as Viewer

Selection of individual files for redundant send/copy possible with 'Mark as not sent'

Fix invalidate CSV files

Replace "formula_params" with "params" key in CSV files footer

Fix data logger name encoding error in SCP

Allow fine-grained sending of CSV files

	Warning
	If you already have secondary and/or tertiary CSV files configured, you must explicitely switch on sending to AmmonitOR, by email, or to a file server now!

Additional RS485 master speed: 1200 bps

Sign all data by default

Support signing and encryption of log and config files for server copy and USB flash drive copy

The comma (",") is not allowed in the data logger name anymore

Fix ZephIR evaluations for more than one height

Effectively turn USB modem switch off, even if no USB modem is connected

Set switch state over display is per default available

Manufacturer administration can be manually started over UI

Newly produced data loggers have individual UI certificates

Fix possible LCD freeze after reboot

Fix LCD backlight switching

Fix data logger name encoding error in snapshots and test email

New ZephIR Live data

New Gill Wind Master M3

Fix evaluation type for Gantner modules

Fix active channels when adding evaluation with evaluation helper

Support secondary and tertiary CSV statistics files

New data types with 8-bit exponent selectable for modbus sensors

New Atonometrics RDE300

Evaluation type and unit can be configured for all sensors of type 'Other Sensor'

Enhanced performance for SCADA stored data request

Fix evaluations using GPS location

Provide default WLAN passphrase for newly produced data loggers

Fix wrong time-stamp in CSV files if summary statistic configured

New formulas in Evaluation Helper

Fix live data evaluation for Thies Clima sensor

New Gill Wind Master 3D Ultrasonic XYZ coordinates

Support period measurement on counter channels C5, C6, C11, and C12 for newly produced Meteo-40, available as P1, P2, P3, and P4

Fix switches state shown in display

Fix ultrasonic sensors wind speed linear formula

	Warning
	In case you are using ultrasonic sensors and version 1.6.2, you must delete and regenerate all files generated with this version!

Fix SCADA stored data request

Allow deletion of multiple selected statistics files

Fix a problem with source data memory overuse if a switch is associated to a sensor

Fix missing latitude and longitude in CSV and admin page when using GPS

Add date and time of last GPS fix in CSV statistics file as gps_fix

Use function code 4 for Iskra MT540 input registers

Fix SCADA Modbus write to holding registers selection

Switch manager supports inverted logic

Increased robustness for RS485 Thies communication

RS485 serial console representation enhancements

New Thies 3D Ultrasonic XYZ coordinates

New RS485 Master serial console

New RS485 sensor SMP10 pyranometer

Record status byte for Thies Ultrasonic 2D and 3D

Fixed send statistics CSV per email if Gust data active

Include SCADA status in Information site

New set one switch over SCADA using Modbus write single coil

Fixed set switches OFF over SCADA

Fixed request stored data over SCADA

Fixed sending of snapshot data to AmmonitOR, broken in 1.6

Fixed unexpected tunnel connection if SMS active

Fix tunnel connection fails on action execution if another action running

New solar zenith angle in evaluation helper

Allow Mosbus RTU broadcast address '0' for sensors

Slope for ultrasonic sensors wind direction available

Fix SiS-13TC-T sensor irradiance not available

Default connection (Ethernet/Modem) is shown in capital letters (uppercase)

Add support for Met One 014mini anemometer

Optionally create gust data files

Include internal voltage and temperature in Switch Manager lists

Add data snapshot to email and server copy

Add slope and offset for 3D ultrasonic sensors vertical wind speed

Update provider helper with current mobile providers and APNs

Fix custom evaluations: allow any input evaluation and not only evaluations of type "other"

Data logger is prepared for later upgrades via USB flash memory

Fix easy cleanup for SCADA registers tables

Increase backlight time for Meteo-40 Revision D from 5 s to 15 s, and allow Admin to deactivate display backlight

Custom evaluations are ordered in CSV between regular evaluations and channels

Optionally copy camera image to a USB flash drive when sending

Allow Admin and User to view and download data logger files on USB flash drive

Use hPa instead of mbar for newly configured pressure sensors

Fix SCADA stored data request timestamp: use unix time and not logger local time

New summary statistics available over SCADA

New set switches state over SCADA

Allow users starting actions via display (requires setting the permission first)

New covariance evaluation

New generic thermo-hygro 5 V -20–80 °C / 10 V

Maximum and minimum statistics available for internal temperature

Statistics for internal channels can be selected

New sensor MESA WSWD Sonic

Add source data download of complete week

Add function to invalidate all statistics CSV files, that have been sent before

Write in SCADA server holding registers optimized

When setting time, check whether files from later dates exist

Fix close tunnel connection if CECS always on

Fix a harmless, but annoying error message when saving the configuration

User interface: fix related to config file download

User interface: minor performance improvement

Force Encryption now also blocks changes on Email and SCADA, and limits live data to about 2 minutes

New evaluations: Sensible Heat Flux, Turbulence Intensity, Obukkhov stability parameter and Inflow angle

Add function to easily regenerate possibly inconsistent CSV files

Make action handling more reliable

Solve problem with switch "Prevent implicit tunnel activation (only recommended for satellite communication)". The tunnel connection was not disabled after "Action online"

Fix wrong date/time stamps in CSV, in cases when first channel had invalid data

Add option to reduce online traffic when logged in, e.g. for satellite connections

SCADA server write in Modbus store is now an atomic operation

New generic Hygro/Thermo sensor -20–80 °C

New Silicon Irradiance Sensor SiS-13TC-T

Fix SCADA modbus acknowledge writing holding registers

Fix SCADA interval for stored data request

Pyranometer Li-Cor LI-200SZ must be connected to analogue channel

Fix a problem with signatures for newly produced Meteo-40

Enhanced EKO Sun Tracker date, time and location synchronization

Logbook more verbose, i.e. messages about CECS status and actions

Minor UI improvements, e.g. faster web service and data logger icon

Fix a problem with CECS mode not possible to change from LC display

Fix a problem with time setting occasionally not working

Fix CMP10 solar sensor

UI: sow CECS and MARS uptime

Fix false handling of missing digital (TMR) wind vane data

	Warning
	In case you have wrong CSV files, generated from version 1.5 to 1.5.7, you have to remove them and regenerate!

Rename Heating Manager to Switch Manager

Add switch management by means of wind speed for solar power plants

Fix precipitation scale factor for Meteo-32 Streaming livedata

Fix change switch state with switch manager

Add easy cleanup for SCADA registers tables

Fix Obukov-length CSV header for AmmonitOR

Fix source data download

Fix Silicon irradiance sensor default slope

Fix automatic CECS reboot method

Add evaluated data to source data view in web interface and to USB flash copy

Add evaluation type and unit to linear equation

Fix ZephIR 300 endianness and statistics

Provide access to stored data over SCADA

Fix ultrasonic wind speed scale factor for Meteo-32 Streaming livedata

	Warning
	In case you are using Meteo-32 Streaming to read wind speed values from ultrasonic sensors, you might need to correct the scale factor at the SCADA master!

Fix generation of partial CSV files

Minor bug fixes in CSV files generation

Fix action 'Only generate CSV'

Use '---' for invalid value in CSV

Fix statistics when using different measurement rates for counters and digitals

Fix generic windvane evaluation

Fix statistics when using different measurement rates are used

	Warning
	In case you have wrong CSV files, generated from version 1.5 to 1.5.3, you have to remove them and re-generate!

Fix data snapshots to AmmonitOR

Add hint for BGAN users on LAN page

Add PT100 variant of Galltec Thermo-Hygro Passive CP

More flexible ways of copying files to USB flash drive by date

New ZephIR certified averaged data

Fix CSV File generation with Thies Clima Sensor US

Fix problem with action colliding with midnight reboot

Remove standard cabinets from user interface

New Apogee pyranometer PYR-PA, PYR-SA

Fix RS485 polling rate for Thies Laser Precipitation Monitor

Add self test for digital clock output

More flexible automatic CECS reboot function

	Note
	If you use SCADA or are using Meteo-40 in 24/7 mode, check the setting Automatic CECS reboot option on the administration page after upgrade!

Fix a precision error in release 1.5 for digital wind vanes

Add support for sensors:

New status evaluation in Evaluations Helper

New direction at maximum speed evaluation in Evaluation Helper

Fix active power and obukhov length in evaluation in Evaluation Helper

Fix application of positive and negative slope and offset to Young Propeller Anemometer

	Note
	If you have different slope values for upwind and downwind, it is necessary to regenerate the CSV files! The slope for downwind will be automatically set to a negative value by the data logger.

Support for SMTPS in addition to STARTTLS for more Email security options

Device Identification available over SCADA

Set date and time over SCADA Modbus communication

CSV stability improvements

Support tilt angle and cardinal direction for SPN1

Improve evaluation view and start messages in LC display

Fix a communication issue, when no AmmonitOR project key is set

Improve GPS reliability

Future upgrades will use HTTPS instead of HTTP, enhancing security

Fix configuring digital channel to power on CECS

Fixed a CSV generation error

Digital signatures refer to uncompressed CSV as canonical, not the compressed files - this might influence your work flow

Fixed a problem with delayed GPS time

GPS location no longer changes configuration

Support for Temperature Sensors 4–20 mA, -30–70 °C and -40–60 °C

Fix for download of encrypted data in web interface

Data encryption supported for USB flash drive copy and download

Support for CSPS RSI sensor

New linear equation, active power and wind direction formulas in Evaluation Helper

Heating manager control by means of voltage measurement allowed

Configurable word endianness for RS485 Modbus Sensors

Include solar radiation summary in CSV files

User interface change: New device page with display and USB flash drive settings

User interface change: Encryption and signature now under Administration

Add a Force Encryption option

Connection check in web interface and via LC display

Fix CSV generation with numerous RS485 errors

Fix Young Wind Monitor missing wind direction evaluation

New HMP155 active and passive sensors

Fix tunnel connectivity, when reconfiguring

Reduce SCADA Modbus server response time to 40 ms

Old CSV files get removed on CECS reboot when not enough memory left

Allow custom clipping for humidity sensors

Fixed a problem with encryption when private key is not available

Fixed a problem with sending pictures via FTP

Enhanced RS485 sensors support

Fixed a problem with preventing sending of CSV files to AmmonitOR or file server

Removed unused tilt angle from sensor helper

Fixed UI air density configuration

Fixed a SCADA performance issue

Fixed a problem with deleting source data memory

Fixed a problem with display showing "Please wait" for a long time

Fixed a problem with Thies Precipitation Monitor

Fixed a CSV generation error in cases where measurement has been stopped for a day by the user

Data snapshot and camera image can be sent to AmmonitOR now, data snapshot is still experimental

UI: show modem quality bar in LC display and web UI

UI: warn about missing WLAN passphrase

UI: don't show Gantner modules as unknown in LC display

Add Thies Precipitation Monitor

Obukhov length possible with 3D ultrasonics

Enhance memory security esp. for SCADA

Thies Clima Sensor uses wind direction offset for brightness direction

Fixed a problem with SCP sending when data logger name contained non-ASCII characters

Added support for Thies Clima Sensor US

Fix wind speed evaluation for Lufft WS

Enhance memory security

Fixed a problem with the SCADA function: In some cases the values were not readable

Fixed a problem with the camera function for data logger with non-ASCII characters in their name

Fixed a problem with the display of values for some RS485 modules

Counter measurement fix: When the clock is set, e.g. by NTP or GPS, under some conditions, the counter value can be wrong. This affected mainly the maximal values

Minor UI fixes

Modem PHS8 is supported

Experimental support for SMS

Complete configuration can be sent to AmmonitOR or via email or FTP/SCP

	Note
	If you don't want to have the configuration file sent to AmmonitOR or via email or FTP/SCP, you have to switch this off in the respective menu.

New scale factor and data type selection for SCADA measurement values

New Unix Time available over SCADA

Easier connection between PC and data logger using link-local connection

Fixed a problem with CSV generation

Fixed providing sum statistic over SCADA

Digital signature available for newly produced data loggers. Contact Ammonit, if this feature is required on a previously purchased device

The heating manager can make use of an optional voltage as additional heating condition, while the humidity has been made optional

The USB flash drive function is activated with a default password for newly produced data loggers

Factory reset and source data deletion is logged in the logbook

Setting of date/time by GPS, NTP, or manually is logged into logbook

Setting the date via GPS is supported, updating the altitude by GPS is not done anymore

An error in the counters calculation for periods ≠ 1 s has been fixed

Minor user interface changes

Fixed a problem sending images via e-mail

Use new algorithm for wind direction maximum and minimum

Show DHCP state also for Tethering connection

New Thies Laser Precipitation Sensor

Memory sizes are indicated in MiB

Error condition recognition for Gill Wind Master

Enhanced Modbus RTU SCADA server performance

New page for AmmonitOR related configuration

Allow sending data to both AmmonitOR and an FTP/SCP server

New densitiy of moist air evaluation

Fix CSV generation with temperature differential evaluations

Correction for Galltec Thermo-Hygro Passive CP

Allow date limit for file transfer (start date) and reset of send status

Improved check when sending test email

Add experimental support for email encryption

Fix NMEA RS485 telegram parser

Enhance modem communication in respect to disconnection

Enhance clock accuracy

Enhance memory protection

Fix Young Monitor and Tech Sun channel order

Fix erroneous recursive CSV file generation

Support for temperature difference evaluation

More WLAN chips are supported: Atheros AR9271, Ralink rt2800, Ralink rt73

Enhanced UI for accessing source data

Minor error corrections, e.g.

New sensors: FarData wind vane, Teknam Thermo-Hygro, Teknam barometric pressure sensor

Enhanced special mode for Meteo-32 wind vane compatibility: No dedicated configuration of Meteo-32 sensors necessary; standard configuration and connection according to manual

Milliseconds in date/time field of statistics file ( .csv) removed; importing software might be configured, if necessary

Switching of CECS status via status input signal, see Administration.

Format of the keyfile.txt changed to INI file format; copying of source data to logbook possible

Minor user interface changes

Speed up and improved robustness of source data download

Speed up some solar evaluations

Enhanced RS485-Sensors error recognition and response

Configurable slope and offset for RS485 ultrasonics horizontal wind speed

Fix RS485-Sensors count statistic when more than one sensor connected

New sensors: Tech-Sen thermo-hygro, Tech-Sen barometric pressure sensor

Correction for status evaluation

Minor user interface changes

New sensors: Setra barometric pressure sensor Model 276 and 278; compatibility for first and second Meteo-32 wind vane

Optimized tunnel traffic

USB connection displayed in status box; data logger name shown in upper right corner

New sensors: Pyranometer SP Lite 2, Gantner e.bloxx A1

Re-enabled reboot at midnight, with exception for SCADA-enabled data loggers

Enhanced flash memory detection

New sensors: Hygro-thermo Galltec KPC MS, passive hygro-thermo Galltec CP, Gantner e.bloxx A3-1 and d.bloxx D1-1, wind vane Vaisala WAV252, Thies precipitation intensity

Support of virtual temperature for Gill wind observer 2D

Better presentation of switches states in live data

Better estimation of sun status for SPN1

User interface enhancements for SCADA

Logbook for registering events

POP-before-SMTP/SMTP-after-POP supported by email function

Better support for USB flash drives

Replacement of tunnel affix by tunnel access code

Download multiple CSV file as ZIP archive

Solved wrong statistics selection (scalar/vector)

Communication enhancements, esp. for satellite modems

Increased memory protection

Support for Sineax Cam Power Meter, e.g. for PCM

Heating manager problem on configuring boundaries corrected

Enhancements in web interface: Statistics calendar

Optional time synchronization via GPS

Heating manager: Temperature and humidity configurable

Support for ISKRA Power Meter, e.g. for PCM

Wind direction offset for ultrasonic sensors added

Timing enhancement for RS485 sensors

Additional route for LAN possible, e.g. for SCADA

Solved sporadic connection failure with modem

Possible wrong timezone corrected, when setting the time manually

Enhancements in web interface for smart phones and small devices

Timeout problem for serial (RS485) SCADA connections corrected

Set default display contrast

Error for Lufft RS485 sensor corrected

Automatic reboot at midnight removed

RS485 serial settings allowed

Further performance enhancements for SCADA

Possible source data corruption problem after second overrun (e.g. after two years) corrected; upgrade must happen before second overrun

Implementation of new "generic" ModBus RTU sensor

Supported temperature measurement using Pt1000 or Pt100 for data loggers with built-in Ethernet interface

Evaluating of virtual temperature for Gill Windmaster Pro 3D, if configured like Thies ultrasonics 2D/3D

Minor user interface corrections

Documenation of heating manager

Performance enhancements for SCADA

Support of data logger with built-in Ethernet interface

New feature: Simple heating manager

Corrected data actualization problem in SCADA

Internet Explorer 8™ and Chrome™ supported

Parallel working of SCADA and modem possible

UI with virtual display keys

Enhanced factory reset

Email sending problem corrected

GPS enhancements

Changes in network shown live in display

CSV files with round time slices

Serial modems work, even if not permanently on

Measurement frequency ⅛s removed

Problem with displaying negative power for pyranometers corrected

Emergency password reset method available by means of Ammonit support for new data loggers

Configuration of longitude, latitude, and altitude, support of KML (e.g. Google Earth™)

USB GPS devices supported

Enhanced user manual

Min and max for wind direction available

Eror when saving sensors corrected

Measurement interruption when upgrading corrected

Measurement range for NRG hygro/thermo sensor corrected

Order of hygro/thermo for Galltec sensor corrected

Corrected error for ICP-CON wind vane module

Enhanced user manual

Detection of under-voltage situation (brown-out) implemented

Configuration of CSD3 optionally with only one voltage channel

Thies wind vane classic with one analog channel supported

SCADA endianess configurable

Overall stability enhancements

More robust CSV creation

Gill Windmaster supported

Power meter GD2000 supported

Virtual temperature Thies ultrasonics 2D/3D evaluated

Turkish language in user interface supported

User interface problem with Internet Explorer™ corrected

Average values for SCADA supported

Gill Wind Obversver is supported

PINs and passwords not visible in the downloaded configuration anymore

Problems with uploading older configuration files solved

CECS mode is saved in the configuration file

New functions to remove all statistics files, all sensors, and for factory reset

Switches in the display shown

Minor changes for upgrade function

Fixing of an potential data corruption error introduced with the last version

Problem with switching of the CECS corrected

Enhanced solar sensors

AmmonitOR connection log supplied with data logger time and time zone

Documentation corrections